FranklinWH battery installers across Greater Melbourne, VIC.

Why the installer matters more than the battery

The Clean Energy Regulator inspected 1,278 home battery installations under the Cheaper Home Batteries Program between July 2025 and April 2026 — more than 60% came back substandard and 1.2% unsafe. Solar Select checks installer approval and current eligibility before matching your Melbourne enquiry. Manufacturer accreditation is a separate check; confirm the credentials relevant to your chosen battery.

What specifically goes wrong on a FranklinWH install

• The aGate rewires how the home’s circuits are managed — this is switchboard-level work where installer quality shows up immediately
• Per-circuit backup decisions made lazily at install time are the difference between the system as designed and the system as marketed
• Generator integration needs correct configuration to behave as an orchestrated source rather than a bolt-on
• Clean Energy Council listing is model-by-model — confirm the exact aPower variant quoted

Request my FranklinWH quotes in Melbourne.

Source: CER inspections, reported by UTS (Apr 2026)

Comparing FranklinWH quotes in Melbourne

We don't publish price bands, because installed prices move constantly and depend on your roof, switchboard and supply. What we can tell you is what to hold constant so three quotes are actually comparable — match these first, then compare after-rebate dollars per usable kWh.

1. How many aPower units, and whether the aGate configuration leaves room to add more later
2. Which circuits the aGate controls individually — per-circuit management is the product, so a quote that skips this detail skips the point
3. Whether the design brings in a generator or EV charging now or leaves provision for later
4. What your existing solar inverter is, since the AC-coupled design keeps it — its age and condition still matter
5. Confirmation the exact model is on the Clean Energy Council approved battery list

A cheaper quote that skips backup hardware, assumes an inverter you don't have, or quietly changes the configuration isn't cheaper — it's a different job.

Want three FranklinWH quotes you can actually compare? Your enquiry goes to up to 3 vetted installers in Melbourne, all quoting the same scope.

Battery rebates in Victoria

• Cheaper Home Batteries Program (federal) — roughly a quarter off the installed battery cost, upfront, paid at its full rate on the first tier of usable capacity and at a reduced rate above that. Applied at quote by the installer, not claimed back later.
• Federal-only in 2026 (VIC) — Victoria runs federal-only on battery rebates in 2026 — the Solar Homes rebate covers panels, not storage. The federal Cheaper Home Batteries discount still applies in full. Full VIC rebate breakdown

The Melbourne numbers

Solar Select's Melbourne study-area aggregation of Clean Energy Regulator data includes 528,883 small-scale systems across 233 postcodes — about 3,481 MW of capacity as at 2026-06. For a FranklinWH retrofit in Melbourne, check the existing inverter and switchboard before choosing the configuration. Ask whether the inverter stays, is replaced, or works alongside another one; installation counts do not answer that for your home.

In the typical Greater Melbourne postcode, new systems averaged about 9.8 kW through 2025. That is the scale of array a FranklinWH battery would be charged from here, so ask each installer to size storage against that generation rather than the headline capacity: the configuration that suits a 9.8 kW roof is not automatically the biggest one quoted.

Five distributors carve up Greater Melbourne: CitiPower in the inner city, Powercor across the west, Jemena in the north-west, AusNet Services through the north-east and outer east, and United Energy south-east of the Yarra. A FranklinWH quote written for a Powercor address does not automatically transfer to an AusNet one — export caps and approval rules move at the boundary.

Melbourne swings from about 7 peak sun hours in Jan to 1.8 in Jun — roughly 3.9× more generation in the sunniest month than the dullest. On a 10 kW array that is around 59.5 kWh a day in Jan against 15.3 kWh in Jun. Size a FranklinWH on the winter figure: FranklinWH is 13.6 kWh per unit, stackable, so the real question at quote stage is what it can actually refill on a 15.3 kWh day, not what it holds on paper.

Install counts and capacity: Clean Energy Regulator postcode data for small-scale installations (CC BY).

What owning a FranklinWH is actually like

Spec sheets stop being interesting about a week after install. These are the things owners notice in year one.

• The aGate’s per-circuit control is what owners end up valuing — choosing which circuits ride through an outage and which shed automatically is a level of control most systems simply do not offer.
• Blackout behaviour includes starting itself from stored energy and running indefinitely with solar — genuine off-grid capability rather than a few hours of ride-through.
• Because it is AC-coupled and inverter-agnostic, it lives happily alongside any existing solar brand — your solar system’s app and the FranklinWH app coexist.
• Generator integration is unusually clean: the aGate treats a generator as one more managed source, which rural owners in particular make real use of.

Four questions to ask any FranklinWH quote

1. Which circuits will the aGate control individually, and which stay on in an outage?
2. How many aPower units does my usage actually need, and what does adding one later involve?
3. How many FranklinWH systems have you commissioned, and who handles a manufacturer claim in year four?
4. Can you show me this exact model on the Clean Energy Council approved battery list?

Grid connection in Melbourne

• Distributor pre-approval — battery systems usually need explicit pre-approval from your distributor: across Greater Melbourne that is CitiPower, Powercor, Jemena, AusNet Services or United Energy, depending on the address. A good installer lodges the application and flags any constraint in the quote — not after.
• Typical export cap ~5 kW — single-phase residential export across Greater Melbourne is typically around 5 kW, though the exact cap depends on which network your address is on. A battery softens the cap — solar that can't export charges the FranklinWH instead of being curtailed.
• 5–15 business days — typical connection-approval turnaround once the installer lodges with your distributor.

Ready for FranklinWH quotes in Melbourne?

Request quotes from up to 3 vetted installers for a FranklinWH in Melbourne — postcode in, quotes out.

Get my FranklinWH quotes for Melbourne

Areas served around Melbourne

Matching covers Greater Melbourne, not just the centre — enquiries route on your postcode. Local solar detail for each suburb:

• Carlton South (3053) · 1.2 km from Melbourne — 205 systems, 2,217 kW installed
• World Trade Centre (3005) · 1.2 km from Melbourne
• East Melbourne (3002) · 1.5 km from Melbourne — 108 systems, 1,043 kW installed
• South Wharf (3006) · 1.5 km from Melbourne — 47 systems, 1,450 kW installed
• Southbank (3006) · 1.7 km from Melbourne
• Carlton (3053) · 1.9 km from Melbourne
• Docklands (3008) · 1.9 km from Melbourne — 120 systems, 2,122 kW installed
• Hotham Hill (3051) · 1.9 km from Melbourne — 340 systems, 2,492 kW installed
• Melbourne University (3052) · 1.9 km from Melbourne — 175 systems, 2,084 kW installed
• Royal Melbourne Hospital (3050) · 1.9 km from Melbourne
• University Of Melbourne (3010) · 1.9 km from Melbourne
• South Melbourne (3205) · 2.1 km from Melbourne — 369 systems, 2,987 kW installed
• Melbourne (3004) · 2.2 km from Melbourne — 26 systems, 631 kW installed
• Fitzroy (3065) · 2.5 km from Melbourne — 395 systems, 2,783 kW installed
• Collingwood (3066) · 2.6 km from Melbourne — 281 systems, 2,702 kW installed
• Collingwood North (3066) · 2.6 km from Melbourne
• Richmond North (3121) · 2.6 km from Melbourne — 1,272 systems, 8,880 kW installed
• St Kilda Road Central (3004) · 2.6 km from Melbourne
• St Kilda Road Melbourne (3004) · 2.6 km from Melbourne
• Domain Road Po (3141) · 2.7 km from Melbourne — 461 systems, 3,268 kW installed
• North Melbourne (3051) · 2.7 km from Melbourne
• Carlton North (3054) · 3.0 km from Melbourne — 488 systems, 2,529 kW installed
• Cremorne (3121) · 3.0 km from Melbourne
• Richmond (3121) · 3.1 km from Melbourne
• Richmond South (3121) · 3.1 km from Melbourne
• Richmond East (3121) · 3.2 km from Melbourne
• Abbotsford (3067) · 3.3 km from Melbourne — 323 systems, 2,610 kW installed
• Albert Park (3206) · 3.4 km from Melbourne — 556 systems, 3,210 kW installed
• West Melbourne (3003) · 3.4 km from Melbourne — 149 systems, 2,232 kW installed
• Parkville (3052) · 3.5 km from Melbourne
• Princes Hill (3054) · 3.5 km from Melbourne
• South Yarra (3141) · 3.5 km from Melbourne
• Burnley North (3121) · 4.0 km from Melbourne
• Chapel Street North (3141) · 4.0 km from Melbourne
• Fitzroy North (3068) · 4.0 km from Melbourne — 1,419 systems, 7,751 kW installed
• Kensington (3031) · 4.0 km from Melbourne — 1,024 systems, 6,399 kW installed
• Middle Park (3206) · 4.1 km from Melbourne
• Port Melbourne (3207) · 4.1 km from Melbourne — 657 systems, 7,748 kW installed
• Victoria Gardens (3121) · 4.2 km from Melbourne
• Clifton Hill (3068) · 4.4 km from Melbourne
• Glen Iris (3146) · 9.3 km from Melbourne — 2,035 systems, 13,540 kW installed
• Avondale Heights (3034) · 10.5 km from Melbourne — 1,007 systems, 5,904 kW installed
• Merlynston (3058) · 10.5 km from Melbourne — 3,712 systems, 23,281 kW installed
• Ormond (3204) · 11.8 km from Melbourne — 2,671 systems, 16,798 kW installed
• Surrey Hills North (3127) · 11.8 km from Melbourne — 1,678 systems, 10,316 kW installed
• Surrey Hills South (3125) · 11.8 km from Melbourne — 1,314 systems, 8,286 kW installed
• McKinnon (3204) · 12.4 km from Melbourne
• Burwood (3125) · 13.3 km from Melbourne

Read before you commit

• FranklinWH aPower review

FranklinWH questions, Melbourne answers

What actually makes FranklinWH different from other batteries in Melbourne?

The aGate. Most battery systems manage the battery; the aGate manages the house — solar, grid, storage, generator and EV charging as one orchestrated system, with individual circuits controllable from the app. The battery itself is deliberately conventional. If that whole-home layer is not something you value, you are paying for capability you will not use — which is the fair way to decide on this brand.

Will FranklinWH work with the solar system I already have for a Melbourne home?

Yes — this is one of its cleanest strengths. The aPower is AC-coupled and inverter-agnostic, so it sits alongside whatever solar brand you run today without touching it. Your solar keeps doing its job; the FranklinWH layer manages where the energy goes. The one caveat: if your existing inverter is near end of life, replacing it is a separate future job this system does not solve.

Is a FranklinWH battery eligible for the federal rebate in Melbourne, VIC?

Eligibility is model-by-model on the Clean Energy Council approved list, so have the installer show you the exact aPower variant on the current list before signing. With a high-end system the rebate is a large number — worth thirty seconds of checking.

How well does FranklinWH handle blackouts if I live in Melbourne?

This is the strongest part of the product. It switches over automatically, can start itself from stored energy with the grid down, and with solar attached can run the managed circuits indefinitely — genuine off-grid capability rather than a few hours of ride-through. The design decision that matters is which circuits the aGate manages: that list, agreed at quote time, is exactly what stays alive.

Can FranklinWH really run a generator and the battery together for Melbourne households?

Yes, and more gracefully than most: the aGate treats a generator as one more energy source to orchestrate, bringing it in automatically under rules you set rather than requiring manual changeover. For rural properties with existing generators this is one of the most practical reasons to shortlist the brand. It still needs configuring properly at install — ask specifically how the generator handover is set up.

Is one aPower unit enough for my home across Greater Melbourne?

For most grid-connected homes, one unit covers an evening comfortably; whether it covers your ambitions depends on what you want the system to do in an outage. Whole-home resilience — the thing FranklinWH is actually built for — often points to two units or more once you add up the circuits you refuse to lose. Do the load maths before deciding, because the aGate architecture makes adding units later straightforward but never free.

In Melbourne, is FranklinWH too new in Australia to trust?

It arrived in 2023, so the local record is real but short — a few years of installs, a local office, and customer scores at the top of the aggregates. That is a genuinely good early signal, not a long one. The sensible hedge is the same as with any newer brand: an installer who has commissioned several of them and will support the system personally, and clarity in writing about who handles a manufacturer claim.

Who installs FranklinWH batteries in Melbourne?

Solar Select is a matching platform for homeowners seeking FranklinWH battery installation in Greater Melbourne. Submit your postcode and requirements to request a match with up to 3 approved installers, subject to current coverage and eligibility. Manufacturer accreditation is verified separately; ask for the credentials relevant to your chosen battery. Free for homeowners.

How do I compare FranklinWH quotes in Melbourne?

Installed prices move constantly and vary by site, so compare on after-rebate dollars per usable kWh rather than headline totals — and only once the scope matches. For this brand the variables that matter are: how many aPower units, and whether the aGate configuration leaves room to add more later; which circuits the aGate controls individually — per-circuit management is the product, so a quote that skips this detail skips the point; whether the design brings in a generator or EV charging now or leaves provision for later. Get all three quotes on the same scope, then compare the installers harder than the numbers.

What battery rebates apply in Melbourne?

The federal Cheaper Home Batteries Program applies nationwide — roughly a quarter off installed cost, upfront, paid at its full rate on the first tier of usable capacity and tapering above that. Because FranklinWH is 13.6 kWh per unit, stackable, how much you collect depends on how the configuration lines up with those tiers, so ask the installer to show the tier split rather than one flat "government incentive" line. VIC runs federal-only on batteries in 2026.

Which distributor approves a FranklinWH connection in Melbourne?

Across Greater Melbourne the poles-and-wires network is CitiPower, Powercor, Jemena, AusNet Services or United Energy, depending on the address — your installer identifies which one at quote stage and lodges with them. The application covers the whole system, so what gets scrutinised depends on the configuration: the aGate rewires how the home’s circuits are managed — this is switchboard-level work where installer quality shows up immediately. Export is typically around 5 kW single-phase, though the exact cap depends on your network, and approval usually runs 5–15 business days once lodged.

Are your Melbourne installers FranklinWH-accredited?

Accreditation is one of the things we look at, and where a FranklinWH-accredited installer covers Greater Melbourne you'll see that in the match. It is deliberately not the only filter — a current accreditation badge says the installer has done the brand's training, not that they wire a good switchboard or come back in year three. Every installer serving Melbourne is vetted on the same bar set out above before they join. Ask the ones you're matched with what FranklinWH work they've actually done, and how much of it, before you sign.

Is a FranklinWH battery worth it in Melbourne?

Melbourne averages 4.3 peak sun hours, so a 10 kW rooftop array generates roughly 36.6 kWh on an average day — enough to cycle a FranklinWH on most days of the year. With Victoria feed-in tariffs typically paying 4.9–12c/kWh while grid power costs 30–35c, every stored kWh you use yourself is worth several times what exporting it earns.

How many solar installations are recorded across Greater Melbourne?

Solar Select's Melbourne study-area aggregation of Clean Energy Regulator data includes 528,883 small-scale systems across 233 postcodes — about 3,481 MW as at 2026-06. These are system counts, not a count of unique homes or FranklinWH installers. For a retrofit, check your existing inverter, switchboard and actual generation before choosing storage; the study-area total cannot establish those details.

Answered what you needed?

Get your up to 3 vetted FranklinWH quotes for Melbourne — free, no obligation.

Get my FranklinWH quotes for Melbourne